- MyEasyControls
- Demo
- Service
- Easycontrol Port Devices Driver Windows 10
- Easycontrol Port Devices Driver Downloads
- Easycontrol Port Devices Drivers
- Easycontrol Port Devices Driver
- Easycontrol Port Devices Driver Download
- MyEasyControls
- Demo
- Service
FAQ EN - Frequently Asked Questions
Having an issue with your display, audio, or touchpad? Whether you're working on an Alienware, Inspiron, Latitude, or other Dell product, driver updates keep your device running at top performance. Step 1: Identify your product above. Step 2: Run the detect drivers scan to see available updates. Step 3: Choose which driver updates to install. Connect the EASYCONTROL to your computer with a USB cable via this port. 7.Settled controller 1:the knob for adjusting the program change. It can’t be edited. MMC Device ID 0.127 Specifies the device ID of the MMC message. Normally you will specify 127. Add MAC address as trusted devices on the router; Open port 5222 and 5223. If you have a smartphone that connects to the same Wi-Fi network and you can send WhatsApp messages, these ports will be open and cannot be the cause of the problem. It is not possible to connect several EasyControl devices in parallel to the EasyControl app or to Alexa. The device you connected to has new features for USB-C that the cable doesn’t support. The device or dongle isn't connected to the correct USB-C port on your PC (or phone). The device or dongle is using an external hub or dock to connect to your PC (or phone). Too many other Alternate Mode devices or dongles are connected to your PC (or phone).
If no or only historical values are displayed in the history graphs in the portal, your device does not transfer any data to the portal.
Approaches to solutions:
- Make sure your device is equipped with the latest firmware.
See 'Software Version' info in the 'Configuration -> System'menu. The version 2.16 or higher must be displayed there. - Check whether it is possible to access www.easycontrols.net from the network in which the device is installed.
- If all these steps are unsuccessful, please call Customer Service at +49 (0)7720-606-742 or +44 (0)1206 228 500.
The use of the Helios Easycontrols portal with any number of devices is generally free of charge.
Easycontrol Port Devices Driver Windows 10
In the future, available premium features can be booked as soon as they are available.
| Why is there a bypass flap in our KWL units? | To direct the cooler and filtered fresh air past the cross-flow heat exchanger directly into your premises. |
| When is the bypass active? | The bypass opens: If the user-defined period of time fits, the fresh air limitation has been exceeded, if the set room temperature is exceeded and if the drawn-in fresh air is cooler than the room temperature. |
| When does the bypass valve close again? | The bypass is only closed when the outdoor air restriction or room set point temperature is not reached. |
| Why does the bypass not close even though the outdoor temperature is higher than your room temperature? | Since your premises are colder than the fresh outside air drawn in, condensation increases. This is done on the wrong side of the device, so that water will escape from your KWL and damage and mould may occur. |
| When the bypass is activated, I get too warm? | If the outside air temperatures are too warm, we recommend that the KWL unit adjusts the reduced range (fan stage 1). This means that they have filtered clean air and a controlled air exchange is guaranteed compared to an open window, for example. |
| How does passive fresh air cooling work? | Some of our KWL (200,300,500) devices have this additional function. Although the room temperature is cooler than the outside temperature, the bypass damper will close despite increased condensation. However, they must also loosen a plug in the KWL unit to ensure that the condensate drains off. |
| What is the meaning of the 'offset' supply air temperature? | This function is active when the supplementary heating is switched on. The set 'Offset' temperature is added to your room set point temperature, so that the bypass damper opens only after reaching the temperature sum. This avoids that the fresh air is heated unnecessarily. |
The sensors and control units can be connected via RJ10 cable into commercial series. In the apparatus which depends on the last bus cable, the termination resistor must be connected.
What happens if one of the series connected sensor fails?
The defective sensor no longer delivers measured values, whereby the control no longer considered this sensor.
All other sensors and controls run without restrictions.
Values of faulty sensors are no longer displayed in the web frontend.
Can multiple controls and sensors be integrated into the system?
Yes!
The following maximum sensor / control units can be connected simultaneously:
- 8 x FTF (Humidity temperature)
- 8 x CO²
- 8 x VOC
- 2 x EM (Expansion module)
- 8 x BEC (Control)
- 1 x KNX / EIB Module.
The regulation is always to the highest standard value.
Default values can come from a time program, short program, control panel or sensor.
Only limited!
Since the simple control element BE does not allow switching between manual and automatic mode, the control with the BE is always running in manual mode.
However, the sensor on-demand control of the device only works in automatic mode. The sensors can not control the device.
The sensors can provide measurements of the portal for long-term recording of the spatial situation.
Prioritization controls BE / BEC and several sensors?
The highest value requested one, whether it comes from a sensor or a control panel.
Exception: The requirements for retirement, party or holiday mode overrides everything!
Do I need necessarily an Internet connection to use the device?
No, there are other ways of device control:
Easycontrol Port Devices Driver Downloads
- The device is connected via a control panel: 3-position switch (BE) or Comfort-control (BEC)
- All EasyControls devices are equipped with a web server inside.
This provides a comfortable interface frontend for the device.
EasyControls is then accessible via the Web browser of any computer, smartphone, tablet, etc at LAN.
Why is easycontrol controlled via a web browser rather than through an app?
Easycontrol Port Devices Drivers
The advantage is that the operation is terminal independent. The active website automatically adjusts the display to the size of the screen and is not linked to the various operating systems such as Android, Apple iOS, Windows, etc. Thus, the user interface is identical on all devices.
Sollte Sie kein Netzwerk-Kabel bis zum Aufstellungsort Ihres Easycontrols Geräts haben, so können Sie dieses auch über WLAN in ein bestehendes Funk-Netzwerk integrieren.Dazu verwenden Sie einfach einen beliebigen Access-Point welcher den Modus 'Client' oder 'Wireless Adapter' beherrscht.
Can multiple EasyControls devices be connected to a KNX / EIB gateway?
Easycontrol Port Devices Driver
No. Unfortunately, this is not possible.
Easycontrol Port Devices Driver Download